How To Install Egress Window Well
This Installation Guideline is intended to requite the installer a general overview on how to correctly install a Basement
Egress Window Well. This Installation Guideline is not intended to replace the Manufacturer's Installation Instructions,
simply to supplement and aggrandize on them. An Installer must follow the Manufacturer's Installation Instructions whenever
they vary from these Guidelines to proceed the Manufacturer's Warranty in force.
Note:
- Information technology is the responsibility of the owner, builder, contractor and or architect to select products that comply with applicable, country and local edifice codes that are appropriate for the application and use. A building permit may be needed.
- REDDCO Inc. is not responsible for claims resulting from the failure of the contractor or homeowner to properly install or maintain the Egress Window, Window Well, and Cover.
- Phone call your local diggers hotline before start excavation to avoid accidental contact with underground utility lines
- Gutters, Down Spouts, Faucets on outside walls, Sprinkler Heads and Sump Pump Outlets should be at to the lowest degree 6 to x anxiety abroad from the window well. All water must be directed away from the well to assure proper drainage.
How do I install an egress window well?
Step 1: Select an Egress Well location
Pace 2: Purchase an Egress Well
Step 3: Mark a centerline and dig the hole
Step iv: Install the Egress Window
Step 5: Drain Pipe Installation
Step 6: Well Bottom Preparation
Stride vii: Setting the Egress Window Well
Step viii: Backfilling the Window Well.
Pace nine: Attach Well Cover, or Grate
Step i: Select an Egress Well location
a) Select a location without or remove, wires, pipes or other utilizes.
b) Due east or south wall locations let for maximum light.
c) Installing a well in the same location equally an existing small basement window is popular.
Step ii: Purchase an Egress Well
a) Make certain the egress well, ladder and cover selected to encounter your electric current State or local residentialegress lawmaking. Meet "What is the International Residential Code " and "What is an Egress Well?"
b) See redi-exit.com for a large selection of Egress Wells and Windows
Footstep 3: Mark a centerline and dig the pigsty
a) Mark a center line on the foundation wall in a higher place where the Basement Egress Window and Basement Egress Well are to exist installed.
b) Use a backhoe to dig a hole large enough to adjust the Basement Egress Well so it is centered on the planned Egress Window opening. Dig a pigsty iv pes wider at the foundation wall, one foot wider than the projection and approximately 19 " greater in depth than the Window Well beingness installed.
c) Clean any backlog dirt off the foundation wall. Measure out from your centerline each fashion to mark the inside dimension of the Window Well and then draw a line plumb and level on each side of the centerline.
d) Draw a level line at the summit height of the Window Well. The Window Well should be 2 to iii inches above last class to allow for proper drainage and cover fit.
Step iv: Install the Egress Window
See How do I Install an Egress Window for detailed instructions.
Pace 5: Drain Pipage Installation
Although it is not required, if the business firm has a foundation drainage system it is strongly recommended that a half-dozen-inch minimum diameter drainage pipe and bleed comprehend be tied into the system, to assure adequate drainage during heavy rains.
Pace six: Well Bottom Grooming
a) Make up one's mind the last mounting location of the Window Well; it should be installed so information technology sits 2 to 3 inches in a higher place final ground level and 3 to 10 inches beneath the window sill.
b) Marking the peak of the Egress Well on the wall.
c) A 12-inch layer of ó inch Coarse Stone is then spread in the pigsty.
d) Extend the 12-inch layer of ó inch Coarse Stone 12 inches across the outside dimensions on all sides of the Egress Well beingness installed
Footstep 7: Setting the Egress Window Well
a) Middle the Well over the window and level information technology.
b) Do not distort the window well during installation or the well cover may not fit properly.
c) Measure the inside of the egress well to clinch it's not wider or narrower than the well purchased if and so, adjust the well prior to attaching information technology to the wall.
d) Check the Window Well'southward inside dimension earlier fastening information technology to the wall to brand certain the well is not distorted, adjust if necessary. Information technology should be installed to exactly the inside width of the well purchased to assure proper encompass fit.
eastward) iii/eight" diameter 10 3" long Tapcon® fasteners or equivalent, installed every 12" are suggested for mounting the well.
f) Drill mounting holes through the Well flanges to accommodate the bore of the fasteners if necessary.
m) Marker on, and drill mounting holes into, the foundation wall to suit the fasteners beingness used.
h) Make clean the flange surfaces that volition mount confronting the foundation wall.
i) Apply a quality polyurethane or low-temperature silicon caulk sealant to the flanges to eliminate any water leakage.
j) Fasten the well to the foundation wall.
thou) Add approximately three inches of boosted ó inch Coarse Rock in the bottom of the egress well past the foundation wall
l) Slope the boosted ó inches of coarse rock away from the foundation wall at a charge per unit of 1 inch per pes. The stone should be no higher than 3 to 4 inches from the bottom of the window sill.
Step 8: Backfilling the Window Well.
a) Use knee braces to support Window Well while backfilling if required past the manufacturer.
b) Backfill the outside of the Window Well by mitt. NOTE: Some manufacturers require the use of stone while others allow using normal soil for fill up.
c) Final grade level around Window Well should gradient away at a rate of ane inch per foot and be no higher than 2 to iii inches from the top of the Window Well.
Annotation: Do Not Use Frozen Clay or Large Rocks to Back Fill the Well
Step 9: Adhere Well Cover, or Grate
Attach Well Cover, or Grate
Authored by: Steven Forman at REDDCO Inc., redi-exit.com, 1/two/2018
Source: https://redi-exit.com/install-egress-well/
Posted by: princeaftek1997.blogspot.com
0 Response to "How To Install Egress Window Well"
Post a Comment